![how to run ten tec pegasus software on win7 how to run ten tec pegasus software on win7](https://s3.manualzz.com/store/data/023476135_1-40787b934e04b08b0492f017ad3547a1-360x466.png)
- #HOW TO RUN TEN TEC PEGASUS SOFTWARE ON WIN7 UPGRADE#
- #HOW TO RUN TEN TEC PEGASUS SOFTWARE ON WIN7 DOWNLOAD#
![how to run ten tec pegasus software on win7 how to run ten tec pegasus software on win7](https://www.dxzone.com/dx30675/n4py-software-.jpg)
If that didn’t work, you can try adjusting the settings Compatibility tab. Select and hold (or right-click) the program file, select Properties, and then select the Compatibility tab. Select and hold (or right-click) it, and then select Open file location. In the search box on the taskbar, type the name of the program or app you want to troubleshoot.
#HOW TO RUN TEN TEC PEGASUS SOFTWARE ON WIN7 UPGRADE#
If you have Bluetooth problems after a Windows 10 upgrade or update, see Fix Bluetooth problems in Windows 10.įirst, try running the compatibility troubleshooter: If you have printer or scanner problems after a Windows 10 upgrade or update, see Fix printer problems after updating or upgrading to Windows 10. It is NOT advisable to feed the digital audio into the MIC input as the least amount of excessive signal or noise will over-drive the first analog stage resulting in transmitted distortion of the digital signal.To check which version and build of Windows you're running, in the search box on the taskbar, enter winver and then select Enter. The MIC input is designed for microphones with both level and impedance considerations. As to the ACC input, it is designed to operate at Line level thus giving a much better TX signal-to-noise ratio. A temperature of 60C or 140 F is acceptable. The heat sink is supposed to be hot, that is what it is there for, that is to expel additional heat. With no fan cooling, 50 watts is a very safe power. As a general rule, I will run 50 to 75 watts of power output although I do have the optional fan for cooling of the PA heatsink. At NO TIME should you see any indication of ALC on the Jupiter. Also, always set the PWR control on the radio for 100 watts and adjust the combination of the FLDIGI transmit audio level, Signalink TX Level and Jupiter Line Gain to attain the desired operating power. the Speech Processing is set to 0 or OFF if you intend to run any digital mode. If this Red LED is not on, then more audio from the computer to the Signalink is required. The Signalink USB does provide a hard PTT command as indicated by the Red LED on the Signalink unit. This should give correct radio control and allow FLDIGI to do the work for you. Then Do Not use HamLib as the selected file but use HamCat from the set-up menu within FLDIGI.
![how to run ten tec pegasus software on win7 how to run ten tec pegasus software on win7](https://i.ebayimg.com/images/g/gC0AAOxyrx5Tlaz7/s-l300.jpg)
This file should be saved to the FLDIGI folder.
#HOW TO RUN TEN TEC PEGASUS SOFTWARE ON WIN7 DOWNLOAD#
In order to control the Jupiter from FLDIGI via CAT control, it is necessary to go to the FLDIGI site, and then to FILES, and then to XMLs files, then to Tentec to download the 538.XML file. Let me try to clarify a few misconceptions. Why are you using VOX for keying ion the rig?īTW the TenTec Jupiter is supported for CAT control by WSJT-X using Hamlib, a CAT interface lead would be a very useful addition to your setup. The TenTec Jupiter does has a PTT input on that 5-pin accessory #1 socket that the SignaLink USB should be able to key if configured correctly. If you need to get your old Jupiter on FT8, this should get you started.Hi Gary, Also if the power level is greater than 25% the heat sink on the Jupiter will get very warm. Be sure to adjust the microphone level so that the red ALC light does not come on during transmit. In the Audio section select the CODEC options for both Input and Output. Do NOT select Jupiter from the rig drop down menu as this will not work. There is no need to test PTT or CAT at the bottom of the Radio section. In the WSJT-X software in the Radio section you set the rig = None. To make this work you set the microphone to “line” in the Jupiter menu. If you are buying it for the first time it comes with the SLCAB5PD cable to plug into the 5 pin accessory #1 socket on the back of the Jupiter. I just recently bought a SignaLink USB interface for the Ten Tec Jupiter.